IEC 60404-8-10 : 2.0

Table of Contents

FOREWORD<br>1 Scope<br>2 Normative references<br>3 Terms and definitions<br>4 Classification<br>5 Designation<br>6 General requirements<br>&nbsp;&nbsp;&nbsp;6.1 Production process<br>&nbsp;&nbsp;&nbsp;6.2 Form of supply<br>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;6.2.1 Strip<br>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;6.2.2 Sheet and plate<br>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;6.2.3 Flats and bars<br>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;6.2.4 Wire rod and wire<br>&nbsp;&nbsp;&nbsp;6.3 Delivery condition and state<br>&nbsp;&nbsp;&nbsp;6.4 Surface condition<br>7 Technical requirements<br>&nbsp;&nbsp;&nbsp;7.1 Magnetic properties<br>&nbsp;&nbsp;&nbsp;7.2 Geometric characteristics and tolerances<br>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;7.2.1 Thickness of flat products<br>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;7.2.2 Diameter or side dimension of long products<br>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;7.2.3 Width of flat products<br>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;7.2.4 Flatness (wave factor) of flat products<br>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;7.2.5 Length <br>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;7.2.6 Edge camber for flat products<br>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;7.2.7 Straightness of hot-rolled flats and bars<br>8 Inspection<br>&nbsp;&nbsp;&nbsp;8.1 General<br>&nbsp;&nbsp;&nbsp;8.2 Selection of samples<br>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;8.2.1 General<br>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;8.2.2 Flat products<br>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;8.2.3 Long products<br>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;8.2.4 Wire rod and wire<br>&nbsp;&nbsp;&nbsp;8.3 Preparation of test specimens<br>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;8.3.1 Coercivity<br>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;8.3.2 Geometrical characteristics and tolerances<br>&nbsp;&nbsp;&nbsp;8.4 Test methods<br>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;8.4.1 General<br>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;8.4.2 Coercivity<br>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;8.4.3 Thickness of flat products<br>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;8.4.4 Width of flat products<br>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;8.4.5 Flatness (wave factor) of flat products<br>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;8.4.6 Edge camber of flat products<br>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;8.4.7 Dimensions of long products<br>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;8.4.8 Straightness of long products<br>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;8.4.9 Retest<br>9 Complaints<br>10 Ordering information<br>Bibliography

Abstract

Describes the general requirements, magnetic properties, geometric characteristics and tolerances as well as inspection procedures for magnetic materials used primarily for relays.

General Product Information

Published
Document Type	Standard
Status	Current
Publisher	International Electrotechnical Committee
Pages
ISBN
Committee	TC 68