IEC 60748-3 : 1.0

Table of Contents

FOREWORD
PREFACE
Cross references index
CHAPTER I: GENERAL
Clause
1. Introductory note
2. Purpose
CHAPTER II: TERMINOLOGY AND LETTER SYMBOLS
1. General terms
2. Terms related to ratings and characteristics
    2.1 Linear amplifiers
    2.2 Voltage and current regulators
    2.3 Analogue signal switching circuits (under consideration)
3. Letter symbols
    3.1 Amplifiers
    3.2 Voltage and current regulators
    3.3 Analogue signal switching circuits (under consideration)
CHAPTER III: ESSENTIAL RATINGS AND CHARACTERISTICS
SECTION ONE - STANDARD FORMAT FOR THE PRESENTATION OF
              PUBLISHED DATA
1. Function
2. Description of circuit
3. Ratings (limiting values)
4. Recommended operating conditions
5. Electrical characteristics
6. Mechanical characteristics and other data
7. Application data
SECTION TWO - OPERATIONAL AMPLIFIERS (HAVING TWO INPUTS
              AND ONE OUTPUT)
1. Function
2. Description of circuit
3. Ratings (limiting values)
4. Recommended operating conditions
5. Electrical characteristics
6. Mechanical characteristics and other data
7. Application data
SECTION THREE - AUDIOAMPLIFIERS, VIDEOAMPLIFIERS AND
                MULTICHANNEL AMPLIFIERS FOR TELECOMMUNICATIONS
1. Function
2. Description of circuit
3. Ratings (limiting values)
4. Recommended operating conditions
5. Electrical characteristics
6. Mechanical characteristics and other data
7. Application data
SECTION FOUR - R.F. AND I.F. AMPLIFIERS
1. Function
2. Description of circuit
3. Ratings (limiting values)
4. Recommended operating conditions
5. Electrical characteristics
6. Mechanical characteristics and other data
7. Application data
SECTION FIVE - VOLTAGE AND CURRENT REGULATORS
1. Function
2. Description of circuit
3. Ratings (limiting values)
4. Recommended operating conditions
5. Electrical characteristics
6. Mechanical characteristics and other data
7. Application data (under consideration)
SECTION SIX - ANALOGUE SIGNAL SWITCHING CIRCUITS
General
1. Functional specifications
2. Description of circuit
3. Ratings (limiting values)
4. Recommended operating conditions
5. Electrical characteristics
6. Mechanical characteristics and other data
7. Application data
CHAPTER IV: MEASURING METHODS
SECTION ONE - GENERAL
1. Basic requirements
2. Specific requirements
3. Application matrix
SECTION TWO - LINEAR AMPLIFIERS (INCLUDING OPERATIONAL
              AMPLIFIERS)
1. Specific requirements
2. Power supply currents
3. Small-signal input impedance
4. Output impedance
5. Input offset voltage of a differential-input linear
    amplifier and bias voltage of a single-ended-input
    linear amplifier
6. Input offset current
7. Input bias current
8. Input offset voltage temperature coefficient
9. Input offset current temperature coefficient
10. Open-loop voltage amplification
11. Cut-off frequency (frequencies)
12. Common-mode rejection ratio
13. Supply voltage rejection ratio
14. Output voltage range (d.c. measurement only) for
    differential amplifiers
15. Response times
16. Common-mode input voltage range
17. Short-circuit output current (of an operational
    amplifier)
18. Cross-talk attenuation (for multiple amplifiers)
19. Upper limiting frequency for full output voltage
    swing
20. Maximum rate of change of the output voltage
    (slew rate)
21. Input bias current temperature coefficient
22. Cut-off frequency, unity-gain frequency
SECTION THREE - VOLTAGE REGULATORS, EXCLUDING
                TWO-TERMINAL (SINGLE-PORT) DEVICES
1. Specific requirements
2. Input regulation coefficient and input stabilization
    coefficient
3. Ripple rejection ratio
4. Load regulation coefficient and load stabilization
    coefficient
5. Output noise voltage
6. Temperature coefficient of regulated output voltage
7. Stand-by current (quiescent current)
8. Short-circuit current
9. Reference voltage
10. Transient response to changes of input voltage
11. Transient response to changes of load current
SECTION FOUR - ANALOGUE SIGNAL SWITCHING CIRCUITS
1. Static on-state resistance (under consideration)
2. Control feedthrough voltage
3. Off-state switch isolation
4. Harmonic distortion (under consideration)
5. Cross-talk attenuation
CHAPTER V: ACCEPTANCE AND RELIABILITY
SECTION ONE - ELECTRICAL ENDURANCE TESTS
1. General requirements
2. Specific requirements
TABLE I
TABLE II

Abstract

Gives standards on the following sub-categories of analogue integrated circuits: - operational amplifiers (having two inputs and one output); - audioamplifiers, videoamplifiers and multichannel amplifiers for telecommunications; - R.F. and I.F. amplifiers; - voltage and current regulators; - analogue signal switching circuits. Should be used with Publications 747-1 and 748-1.

General Product Information

Published
Document Type	Standard
Status	Current
Publisher	International Electrotechnical Committee
Pages
ISBN
Committee	SC 47A
Supersedes	IEC 60148B : 1979