AS 1631-1994 (R2018)

Table of Contents

1 -  AS 1631-1994 CAST GREY AND DUCTILE IRON NON-PRESSURE PIPES AND FITTINGS
4 -  PREFACE
5 -  CONTENTS
6 -  1 SCOPE
6 -  2 REFERENCED DOCUMENTS
7 -  3 DEFINITIONS
7 -  3.1 Blank end fitting
7 -  3.2 Coating
7 -  3.3 Component
7 -  3.4 Effective length
7 -  3.5 Fettling
7 -  3.6 Finish
7 -  3.7 Left-hand or right-hand fitting
7 -  3.8 Lipped joint
7 -  3.9 Lining
7 -  4 MATERIAL
8 -  5 DESIGN OF FITTINGS
8 -  5.1 General
8 -  5.2 Connection ends
8 -  6 DIMENSIONS OF PIPES AND FITTINGS
8 -  6.1 Diameter and thickness
8 -  6.2 Length of pipes
8 -  6.3 Overflow relief fittings
9 -  7 MANUFACTURE AND FINISH
9 -  7.1 Quality of metal
9 -  7.2 Mode of casting
9 -  7.3 Heat treatment
9 -  7.4 Finish
9 -  8 STRAIGHTNESS
9 -  9 HYDROSTATIC PRESSURE TEST
9 -  9.1 Pipes and fittings
9 -  9.2 Jointing systems
9 -  9.3 Reflux valve
9 -  10 JOINT DESIGN AND MATERIALS
9 -  10.1 General
10 -  10.2 Caulked or elastomeric-ring joints
10 -  10.3 Bolted gland joints
11 -  10.4 Lipped joints
11 -  11 INSPECTION OPENINGS
13 -  12 TEST OPENINGS
13 -  13 SADDLE FITTINGS
13 -  14 COATING AND LINING
13 -  14.1 General
13 -  14.2 Coatings
14 -  14.3 Linings
14 -  14.4 Handling
14 -  15 MARKING
14 -  15.1 Marking requirements
15 -  15.2 Certification mark
15 -  15.3 Components
16 -  APPENDIX A - INFORMATION TO BE SUPPLIED WITH ORDER
17 -  APPENDIX B - TYPICAL DESIGNS OF CAST IRON NON-PRESSURE PIPE FITTINGS
22 -  APPENDIX C - PROCEDURE FOR CEMENT MORTAR LINING
22 -  C1 GENERAL
22 -  C2 PROPORTIONING OF MATERIALS
22 -  C3 MEASUREMENT AND MIXING OF MATERIALS
22 -  C4 PIPE OR FITTING SURFACE
22 -  C5 APPLICATION
23 -  C6 THICKNESS
23 -  C7 FINISH
23 -  C8 REPAIR OF DEFECTS
23 -  C9 CURING OF CEMENT MORTAR LININGS
23 -  C10 RELINING
24 -  APPENDIX D - MEANS FOR DEMONSTRATING COMPLIANCE WITH THIS STANDARD
24 -  D1 SCOPE
24 -  D2 STATISTICAL SAMPLING
24 -  D3 PRODUCT CERTIFICATION
24 -  D4 SUPPLIER’S QUALITY SYSTEM
25 -  D5 OTHER MEANS OF ASSESSMENT

Abstract

Specifies performance and general requirements for grey and ductile cast iron pipes and fittings up to nominal size DN 300 intended to be used where internal working pressure is considered negligible. An Appendix illustrates preferred designs of pipe fittings.

RECONFIRMATION NOTICE
Major stakeholders of this publication have reviewed the content of this publication and in accordance with Standards Australia procedures for reconfirmation, it has been determined that the publication is still valid and does not require change.
Certain documents referenced in the publication may have been amended since the original date of publication. Users are advised to ensure that they are using the latest versions of such documents as appropriate, unless advised otherwise in this Reconfirmation Notice.
Approved for reconfirmation in accordance with Standards Australia procedures for reconfirmation on 29 August 2018.

Scope

This Standard specifies requirements for cast grey iron (flake graphite) and ductile iron non-pressure pipes and fittings up to nominal size DN 300, and intended to be used where the internal working pressure is negligible.
Where resistance to internal pressure is of prime importance, reference should be made to AS 2280, AS 2544 and AS 1724.
NOTE: Guidelines on information that should be provided by the purchaser or agreed upon at the time of enquiry or order are given in Appendix A. Typical designs of fittings are given in Appendix B.

General Product Information

Published
Document Type	Standard
Status	Current
Publisher	Standards Australia
ProductNote	Reconfirmed 21/09/2018. This standard has been reconfirmed in Australia in 2018 and remains current in New Zealand. Reconfirmation Notice 21/09/2018
Pages
ISBN
Committee	WS-005
Supersedes	AS 1631-1974 DR 93079