AS 2497.1-2001 (R2013)

Table of Contents

1 -  AS 2497.1-2001 PROCEDURES FOR ACCEPTANCE TESTING OF REFRACTORY PRODUCTS - BATCH PROCEDURE
4 -  PREFACE
5 -  CONTENTS
6 -  SECTION 1 SCOPE AND GENERAL
6 -  1.1 SCOPE
6 -  1.2 APPLICATION
6 -  1.3 REFERENCED DOCUMENTS
6 -  1.4 DEFINITIONS
6 -  1.4.1 Acceptable quality level (AQL)
6 -  1.4.2 Batch or lot (inspection)
7 -  1.4.3 Batch, lot or population size
7 -  1.4.4 Consumer’s risk
7 -  1.4.5 Fraction defective
7 -  1.4.6 Increment
7 -  1.4.7 Individual value
7 -  1.4.8 Inspection level
7 -  1.4.9 Item, unit, unit of product
7 -  1.4.10 Limiting quality (LQ)
7 -  1.4.11 Mean (of sample)
7 -  1.4.12 Operating characteristic (OC) curve
7 -  1.4.13 Population
7 -  1.4.14 Producer’s risk
8 -  1.4.15 Sample
8 -  1.4.16 Size of the sample
8 -  1.4.17 Specification limit
8 -  1.4.18 Standard deviation
8 -  1.5 NOTATION
9 -  SECTION 2 METHODS
9 -  2.1 VARIABLES AND ATTRIBUTES
9 -  2.1.1 Variables
9 -  2.1.2 Attributes
9 -  2.1.3 Comparison of use
9 -  2.2 PRACTICAL CONSIDERATIONS
9 -  2.2.1 General
9 -  2.2.2 Batch quality measurement
9 -  2.2.3 Item size
10 -  2.2.4 Inspection by variables
10 -  2.2.5 Multiple properties
11 -  2.3 GUIDE TO CHOICE OF METHODS
12 -  2.4 SUGGESTIONS FOR APPROPRIATE AQL, INSPECTION LEVEL, PRODUCER'S RISK, LQ, CONSUMER'S RISK AND SPECIFICATION LIMIT
12 -  2.4.1 AQL Values
12 -  2.4.2 Inspection level
13 -  2.4.3 Producer’s and consumer’s risks
13 -  2.4.4 LQ Values
14 -  2.4.5 Specification limit (U or L)
15 -  SECTION 3 RECOMMENDED SAMPLING PLANS
15 -  3.1 SAMPLING INSPECTION BY VARIABLES-METHOD 1
15 -  3.1.1 Introduction
15 -  3.1.2 Sampling procedure for Method 1 (see Figure 3.1)
15 -  3.1.3 Example of applying Method 1
17 -  3.2 SAMPLING INSPECTION BY ATTRIBUTES-METHOD 2
17 -  3.2.1 Introduction
18 -  3.2.2 Sampling procedure for Method 2 (see Figure 3.2)
18 -  3.2.3 Example of applying Method 2
21 -  SECTION 4 ALTERNATIVE SAMPLING PLANS
21 -  4.1 SAMPLING INSPECTION BY VARIABLES-METHOD 1A
21 -  4.1.1 Introduction
21 -  4.1.2 Sampling procedure for Method 1A (see Figure 4.1)
22 -  4.1.3 Example of applying Method 1A
23 -  4.1.4 Example of application to multiple properties
24 -  4.2 SAMPLING INSPECTION BY ATTRIBUTES-METHOD 2A
24 -  4.2.1 Introduction
24 -  4.2.2 Sampling procedure for Method 2A (see Figure 4.2)
25 -  4.2.3 Examples of applying Method 2A
28 -  SECTION 5 SAMPLING COSTS
28 -  5.1 SAMPLING COST CONSIDERATIONS FOR VARIABLES AND ATTRIBUTES
28 -  5.2 USE OF COST INFORMATION (AS 1399 AND WETHERILL AND CHIU*)
30 -  SECTION 6 REPORT ON SAMPLING
31 -  APPENDIX A - REFERENCE DOCUMENTS
32 -  APPENDIX B - TABLE OF DEFINITIONS
33 -  APPENDIX C - USE AND FUNCTIONS OF THE OC CURVE
36 -  APPENDIX D - TABLES FOR INSPECTION BY VARIABLES
39 -  APPENDIX E - SAMPLING AND SAMPLING TECHNIQUES
39 -  E1 SAMPLING
40 -  E2 METHODS OF TAKING INCREMENTS
40 -  E2.1 Sample taken from a conveyor belt (as per ISO 8656-1)
40 -  E2.2 Sampling from a wagon, truck, or container (as per ISO 8656-1)
42 -  APPENDIX F - TABLES FOR INSPECTION BY ATTRIBUTES
45 -  APPENDIX G - LIST OF SYMBOLS

Abstract

Sets out the methodology for the acceptance testing of refractory products based on minimum quality levels associated with an agreed specification.

RECONFIRMATION NOTICE
Technical Committee MN-007 has reviewed the content of this publication and in accordance with Standards Australia procedures for reconfirmation, it has been determined that the publication is still valid and does not require change.
Certain documents referenced in the publication may have been amended since the original date of publication. Users are advised to ensure that they are using the latest versions of such documents as appropriate, unless advised otherwise in this Reconfirmation Notice.
Approved for reconfirmation in accordance with Standards Australia procedures for reconfirmation on 4 April 2013.
The following are represented on Technical Committee MN-007:

Australian Institute of Mining and Metallurgy
Australian Ceramic Society
Bureau of Steel Manufacturers of Australia
Cement Industry Federation
CSIRO Manufacturing & Materials Technology
Institute of Refractories Engineers
Refractories Manufacturers Association of Australia
The University of New South Wales


To view or download a copy of the reconfirmation notice please go to the reconfirmation link near the top of this page.

Scope

This Standard sets out the methodology for the acceptance testing of refractory products based on minimum quality levels associated with an agreed specification.
The Standard is suitable for shaped or unshaped products, raw materials or for a product in an intermediary phase. This Standard is applicable to all situations where a minimum quality level, as opposed to a mean quality level, is required for harm minimization.
This Standard does not cover the varied quality control methods used to meet performance requirements.

General Product Information

Published
Document Type	Standard
Status	Current
Publisher	Standards Australia
ProductNote	Reconfirmed 26-07-2013
Pages
ISBN
Committee	MN-007
Supersedes	AS 2497-1981 DR 00365 CP