AS 1774.4.1-2002 (R2013)

Table of Contents

1 -  AS 1774.4.1-2002 REFRACTORIES AND REFRACTORY MATERIALS-PHYSICAL TEST METHODS - PREPARATION OF TEST PIECES-BY CASTING
1 -  1 SCOPE
1 -  2 REFERENCE DOCUMENTS
1 -  3 DEFINITIONS
2 -  4 PRINCIPLE
2 -  5 SAFETY
2 -  6 APPARATUS
2 -  6.1 Mixer
2 -  6.2 Vibrating table
2 -  6.3 Mould
2 -  6.4 Clamp
2 -  6.5 Drying oven
2 -  6.6 Weighing device
2 -  6.7 Sample divider
2 -  6.8 Thermometer
2 -  6.9 Timing device
3 -  7 PROCEDURE
3 -  7.1 Sample preparation
3 -  7.2 Mixing
3 -  7.3 Casting
4 -  7.4 Curing and drying
4 -  8 PRECISION
4 -  9 REPORT
5 -  APPENDIX A - METHODS FOR MEASURING CONSISTENCY OF UNSHAPED CASTABLE REFRACTORIES
5 -  A1 SCOPE
5 -  A2 PRINCIPLE
5 -  A2.1 Tap flow method
5 -  A2.2 Vibration flow method
5 -  A2.3 Self flow method
5 -  A3 APPARATUS
5 -  A3.1 Tap flow table and mould
5 -  A3.2 Callipers
5 -  A3.3 Tamper
5 -  A3.4 Trowel
5 -  A3.5 Polythene sheet
6 -  A3.6 Vibration table
6 -  A3.7 Timing device
6 -  A4 PROCEDURE
6 -  A4.1 Determination of tap flow
6 -  A4.2 Determination of vibration flow
6 -  A4.3 Determination of self flow
7 -  A5 CALCULATION
7 -  A6 PRECISION DATA AND RUGGEDNESS TESTING
7 -  A7 REPORT

Abstract

Sets out a procedure for laboratory preparation of test pieces by casting.

RECONFIRMATION NOTICE
Technical Committee MN-007 has reviewed the content of this publication and in accordance with Standards Australia procedures for reconfirmation, it has been determined that the publication is still valid and does not require change.
Certain documents referenced in the publication may have been amended since the original date of publication. Users are advised to ensure that they are using the latest versions of such documents as appropriate, unless advised otherwise in this Reconfirmation Notice.
Approved for reconfirmation in accordance with Standards Australia procedures for reconfirmation on 4 April 2013.
The following are represented on Technical Committee MN-007:

Australasian Institute of Mining and Metallurgy
Australian Ceramic Society
Bureau of Steel Manufacturers of Australia
Cement Industry Federation
CSIRO Manufacturing & Materials Technology
Institute of Refractories Engineers
Refractories Manufacturers Association of Australia
The University of New South Wales


To view or download a copy of the reconfirmation notice please go to the reconfirmation link near the top of this page.

Scope

This Standard describes a procedure for laboratory preparation of test pieces by casting.
NOTE: The values obtained from test pieces prepared using this method may not correspond with those obtained from test pieces prepared using non-vibratory, or other vibratory, methods.
This Standard applies to dense, mediumweight and lightweight castables containing either hydraulic cements or other binders. It applies to conventional and low cement castables and any other type of refractory castable that can be installed by a casting process.
NOTE: Preparation of test pieces by gunning is covered by AS 1774.4.5, Refractories and refractory materials—Physical test methods, Method 4.5: Preparation of test pieces—Gunning refractories.
A method for measuring the consistency of unshaped castable refractories is given in Appendix A.

General Product Information

Published
Document Type	Standard
Status	Current
Publisher	Standards Australia
ProductNote	Reconfirmed 16-07-2013
Pages
ISBN
Committee	MN-007
Supersedes	AS 1774.4.1-1990 AS 1774.4.2-1992 DR 01328 CP