AS 2439.2-2007

Perforated plastics drainage and effluent pipe and fittings Perforated effluent pipe and associated fittings for sewerage applications

Standards Australia

More details

More info

1 - AS 2439.2-2007 PERFORATED PLASTICS DRAINAGE AND EFFLUENT PIPE AND FITTINGS - PERFORATED EFFLUENT PIPE AND ASSOCIATED...
4 - PREFACE
5 - CONTENTS
6 - SECTION 1 SCOPE AND GENERAL
6 - 1.1 SCOPE
6 - 1.2 APPLICATION
6 - 1.3 REFERENCED DOCUMENTS
6 - 1.4 DEFINITIONS
6 - 1.5 TYPES
6 - 1.6 CLASSIFICATION
7 - SECTION 2 GENERAL REQUIREMENTS
7 - 2.1 SCOPE OF SECTION
7 - 2.2 MATERIALS
7 - 2.3 FREEDOM FROM DEFECTS
7 - 2.3.1 General
7 - 2.3.2 Spigot ends
7 - 2.4 DIMENSIONS
7 - 2.4.1 Diameter
8 - 2.4.2 Length
9 - SECTION 3 PERFORATIONS
9 - 3.1 TYPE 3 PIPE
9 - 3.2 TYPE 4 PIPE
10 - 3.3 FITTINGS
11 - SECTION 4 STORAGE AND TRANSPORT
12 - SECTION 5 PERFORMANCE REQUIREMENTS
12 - 5.1 CONDITIONING OF TEST SPECIMENS
12 - 5.2 BENDING (Type 3 pipe only)
12 - 5.3 STRAIGHTENING (Type 3 pipe only)
12 - 5.4 HIGH TEMPERATURE IMPACT RESISTANCE
12 - 5.5 LOW TEMPERATURE IMPACT RESISTANCE
12 - 5.6 ELONGATION (Type 3 pipe only)
12 - 5.7 PIPE STIFFNESS
12 - 5.8 PERFORATION DEFORMATION
12 - 5.8.1 Type 3 pipe
13 - 5.8.2 Type 4 pipe
13 - 5.9 JOINT SEPARATION (Type 3 pipe only)
13 - 5.10 MARKING
13 - 5.10.1 Type 3 pipe
13 - 5.10.2 Type 4 pipe
14 - APPENDIX A - MEANS FOR DEMONSTRATING COMPLIANCE WITH THIS STANDARD
14 - A1 SCOPE
14 - A2 RELEVANCE
14 - A3 DEFINITIONS
14 - A3.1 Acceptable quality level (AQL)
14 - A3.2 Batch
14 - A3.3 Batch release test
14 - A3.4 Inspection level
14 - A3.5 Lot
14 - A3.6 New formulation
15 - A3.7 Process verification test (PVT)
15 - A3.8 Sample
15 - A3.9 Sampling plan
15 - A3.10 Type test (TT)
15 - A4 PRODUCT CERTIFICATION
15 - A5 MINIMUM SAMPLING AND TESTING FREQUENCY PLAN
15 - A5.1 General
15 - A5.2 Retesting
16 - A5.3 Rejection after test
16 - A6 NEW FORMULATION
18 - APPENDIX B - MEASUREMENT OF DIMENSIONS
18 - B1 SCOPE
18 - B2 APPARATUS.
18 - B3 PREPARATION OF TEST SPECIMENS
18 - B3.1 Diameter-Outside and inside
18 - B3.2 Length
18 - B3.3 Perforations
18 - B4 TEST PROCEDURES
19 - B5 REPORT
19 - B5.1 Outside diameter
19 - B5.2 Inside diameter
19 - B5.3 Length
19 - B5.4 Perforations
20 - APPENDIX C - BENDING TEST (TYPE 3 ONLY)
20 - C1 SCOPE
20 - C2 PRINCIPLE
20 - C3 APPARATUS
20 - C4 PREPARATION OF TEST SPECIMENS
20 - C5 TEST PROCEDURE
20 - C6 REPORT
21 - APPENDIX D - STRAIGHTENING TEST AT 0°C (TYPE 3 ONLY)
21 - D1 SCOPE
21 - D2 PRINCIPLE
21 - D3 APPARATUS
21 - D4 PREPARATION OF TEST SPECIMENS
21 - D5 TEST PROCEDURE
21 - D6 REPORT
22 - APPENDIX E - HIGH TEMPERATURE IMPACT RESISTANCE
22 - E1 SCOPE
22 - E2 PRINCIPLE
22 - E3 APPARATUS
22 - E4 PREPARATION OF TEST SPECIMENS
22 - E5 TEST PROCEDURE
22 - E6 REPORT
23 - APPENDIX F - LOW TEMPERATURE IMPACT RESISTANCE
23 - F1 SCOPE
23 - F2 PRINCIPLE
23 - F3 APPARATUS
23 - F4 PREPARATION OF TEST SPECIMENS
23 - F5 TEST PROCEDURE
23 - F6 REPORT
24 - APPENDIX G - ELONGATION AND PERFORATION DEFORMATION (TYPE 3 ONLY)
24 - G1 SCOPE
24 - G2 PRINCIPLE
24 - G3 APPARATUS
24 - G4 PREPARATION OF TEST SPECIMENS
24 - G5 TEST PROCEDURE
24 - G6 CALCULATION
25 - G7 REPORT
25 - G7.1 Pipe elongation
25 - G7.2 Perforation deformation
26 - APPENDIX H - PERFORATION DEFORMATION
26 - H1 SCOPE
26 - H2 PRINCIPLE
26 - H3 APPARATUS
26 - H4 PREPARATION OF TEST SPECIMENS
26 - H5 TEST PROCEDURE
26 - H6 CALCULATIONS
27 - H7 REPORT
27 - H7.1 Pipe stiffness
27 - H7.2 Perforation deformation (Type 4 only)
28 - APPENDIX I - JOINT SEPARATION (TYPE 3 ONLY)
28 - I1 SCOPE
28 - I2 PRINCIPLE
28 - I3 APPARATUS
28 - I4 PREPARATION OF TEST SPECIMEN
28 - I5 TEST PROCEDURE
28 - I6 REPORT

Abstract

Specifies requirements for perforated plastics effluent pipe and associated fittings intended for effluent discharge.

Scope

This Standard specifies requirements for perforated plastics effluent pipe and associated fittings intended for effluent discharge.

General Product Information

Published
Document Type	Standard
Status	Current
Publisher	Standards Australia
Pages
ISBN
Committee	PL-021
Supersedes	AS 2439.2-1983 DR 05547