AS 3585-2008 (R2019)

Table of Contents

1 -  AS 3585-2008 END FITTINGS FOR SYNTHETIC FLAT-WEBBING AND ROUND SLINGS
4 -  PREFACE
5 -  CONTENTS
6 -  1 SCOPE
6 -  2 REFERENCED DOCUMENTS
7 -  3 DEFINITIONS
7 -  3.1 Competent person
7 -  3.2 Self-coloured
7 -  3.3 Shall
7 -  3.4 Should
7 -  3.5 Working load limit (WLL)
7 -  4 TYPES
10 -  5 MATERIAL
10 -  6 DESIGN AND MANUFACTURE
10 -  6.1 Dimensions
10 -  6.2 Forgings
10 -  6.3 Welded components
10 -  6.4 Heat treatment
11 -  6.5 Surface finish
11 -  6.6 Finishing
11 -  7 MARKING
11 -  8 MECHANICAL PROPERTIES
11 -  8.1 Strength
11 -  8.2 Permanent set
11 -  8.3 Ductility
12 -  9 TYPE TESTING OF MECHANICAL PROPERTIES
12 -  9.1 General
12 -  9.2 Test for deformation
12 -  9.3 Static tensile test
12 -  9.4 Examination for articulation and relative movement
12 -  9.5 Acceptance criteria for type tests
12 -  10 MANUFACTURING TESTS
12 -  10.1 Grade T forged steel components
12 -  10.2 Proof load test-Other fittings
12 -  10.2.1 General
13 -  10.2.2 Requirements
13 -  10.3 Static tensile test-Other fittings
13 -  10.4 Test Certificate
15 -  APPENDIX A - INFORMATION THAT SHOULD BE SUPPLIED WITH ENQUIRIES AND ORDERS
16 -  APPENDIX B - DETERMINATION OF WORKING LOAD LIMIT (WLL)
17 -  APPENDIX C - CONDITIONS FOR APPLICATION OF TEST FORCES
18 -  APPENDIX D - MEANS FOR DEMONSTRATING COMPLIANCE WITH THIS STANDARD
18 -  D1 SCOPE
18 -  D2 STATISTICAL SAMPLING
18 -  D3 PRODUCT CERTIFICATION
19 -  D4 SUPPLIER’S QUALITY MANAGEMENT SYSTEM
19 -  D5 OTHER MEANS OF ASSESSMENT
20 -  APPENDIX E - STANDARDS FOR COMPONENTS USED IN LIFTING SYSTEMS

Abstract

Specifies requirements for the manufacture, marking, and testing of metal end fittings that may be attached to the ends of flat synthetic webbing to form slings complying with AS 1353.1 or may be attached to synthetic fibre round slings complying with AS 4497.1.

RECONFIRMATION NOTICE
Technical Committee ME-025 has reviewed the content of this publication and in accordance with Standards Australia procedures for reconfirmation, it has been determined that the publication is still valid and does not require change.
Certain documents referenced in the publication may have been amended since the original date of publication. Users are advised to ensure that they are using the latest versions of such documents as appropriate, unless advised otherwise in this Reconfirmation Notice.
Approved for reconfirmation in accordance with Standards Australia procedures for reconfirmation on 02 January 2019.
The following are represented on Technical Committee ME-025:
Australian Chamber of Commerce and Industry
Australian Diecasting Association
Australian Industry Group
Chamber of Commerce and Industry Queensland
Crane Industry Council of Australia
Department of Defence (Australian Government)
Engineers Australia
Lifting Equipment Engineers Association
National Association of Testing Authorities Australia
SafeWork NSW
The Institute of Quarrying Australia
WorkSafe Victoria

Scope

This Standard specifies requirements for metal end fittings that may be attached to the ends of flat synthetic webbing to form slings complying with AS 1353.1 or may be attached to synthetic fibre round slings complying with AS 4497.1.
NOTES:
1 Guidance on information that should be supplied with enquiries and orders is given in Appendix A.
2 Means for demonstrating compliance with this Standard are given in Appendix D.
3 Standards for components used in lifting systems are listed in Appendix E.

General Product Information

Published
Document Type	Standard
Status	Current
Publisher	Standards Australia
ProductNote	Reconfirmation Notice 01/02/2019 Reconfirmed 01/02/2019. This standard has been reconfirmed in Australia in 2019 and remains current in New Zealand.
Pages
ISBN
Committee	ME-025
Supersedes	DR 06579 CP